Hi,
Ok, I got motiveded again and last night I restarted my last project, YAHOO :-)
But ... I need to create weld lines, but is there a good and easy way to simulate this?
I don't know if this maters but I want to ad a welder to the dio and he will use a oxygen-acetylene gas welding tool.
Scratchbuilders!: Armor/AFV
This is a group for armor scratchbuilding questions, topics and projects.
This is a group for armor scratchbuilding questions, topics and projects.
Hosted by Mike Kirchoff
Creating weldseams?
Roadkill
Antwerpen, Belgium
Member Since: June 09, 2002
entire network: 2,029 Posts
KitMaker Network: 0 Posts
Member Since: June 09, 2002
entire network: 2,029 Posts
KitMaker Network: 0 Posts
Posted: Saturday, November 16, 2002 - 11:18 PM UTC
Posted: Sunday, November 17, 2002 - 12:07 AM UTC
Hi,
A thin line of Milliput scribed with the point of a X-acto that stops where the welder has its welding point.
HTH
A thin line of Milliput scribed with the point of a X-acto that stops where the welder has its welding point.
HTH
ArmouredSprue
South Australia, Australia
Member Since: January 09, 2002
entire network: 1,958 Posts
KitMaker Network: 720 Posts
Member Since: January 09, 2002
entire network: 1,958 Posts
KitMaker Network: 720 Posts
Posted: Sunday, November 17, 2002 - 02:16 AM UTC
well,
I suscefull use the hot knife method....make a piece of thin stretched sprue, and glue it to the model using liquid glue....once in place, take a fine needle and warm it on an open flame, till it gets red....(please insert the needle into a piece of wood first) and make the weldseam along the stretched sprue on the model....after cool, just brush some liquid glue to soften the edges....
It´s easy and effective, try and you´ll see!
Cheers
I suscefull use the hot knife method....make a piece of thin stretched sprue, and glue it to the model using liquid glue....once in place, take a fine needle and warm it on an open flame, till it gets red....(please insert the needle into a piece of wood first) and make the weldseam along the stretched sprue on the model....after cool, just brush some liquid glue to soften the edges....
It´s easy and effective, try and you´ll see!
Cheers
Tin_Can
Florida, United States
Member Since: January 26, 2002
entire network: 1,560 Posts
KitMaker Network: 344 Posts
Member Since: January 26, 2002
entire network: 1,560 Posts
KitMaker Network: 344 Posts
Posted: Sunday, November 17, 2002 - 04:17 AM UTC
Paulo, here's a sample article from FSM that you might find helpful. This article was in FSM a few months ago. Here's the link:
http://www.finescale.com/fsm/Magazine/SampleFeatures/Samples.html
http://www.finescale.com/fsm/Magazine/SampleFeatures/Samples.html
Roadkill
Antwerpen, Belgium
Member Since: June 09, 2002
entire network: 2,029 Posts
KitMaker Network: 0 Posts
Member Since: June 09, 2002
entire network: 2,029 Posts
KitMaker Network: 0 Posts
Posted: Monday, November 18, 2002 - 09:49 AM UTC
Ok
I got a few problems .
I got my framework done for my dummy-tank diorama (2 of them) and now I want to put welding seams on the intersections, that is why I made the previos post, but ... I don't seem to get it right
I tried the millyput way (won't stick), the spreu (and glue) way (does not form nicley around the rod) but is does not work.
I think that the problem is that there is no real flat surface, I mean the whole frame is made of 3mm rod. I now have a lot of intersections where I need to put some weld lines on.
I have made a crude 3D skets of the framework before I started and since my digital camera is broken I can't give you a picture of the builded frameworks, but I hope you see what I mean.
Any suggestions are more than welcome
I got a few problems .
I got my framework done for my dummy-tank diorama (2 of them) and now I want to put welding seams on the intersections, that is why I made the previos post, but ... I don't seem to get it right
I tried the millyput way (won't stick), the spreu (and glue) way (does not form nicley around the rod) but is does not work.
I think that the problem is that there is no real flat surface, I mean the whole frame is made of 3mm rod. I now have a lot of intersections where I need to put some weld lines on.
I have made a crude 3D skets of the framework before I started and since my digital camera is broken I can't give you a picture of the builded frameworks, but I hope you see what I mean.
Any suggestions are more than welcome
AIRB842586
Arizona, United States
Member Since: October 09, 2002
entire network: 261 Posts
KitMaker Network: 0 Posts
Member Since: October 09, 2002
entire network: 261 Posts
KitMaker Network: 0 Posts
Posted: Tuesday, November 19, 2002 - 02:33 PM UTC
What materials did you finally end up using for the framework? I saw it was 3mm rod but is it wood, plastic, brass...? I'm trying to think of what may work, but I don't know what will stick to your project and what won't, make sense? I'll keep brainstorming ideas If I come up with anything worth mentioning I'll let ya know.
Matt
Matt
Roadkill
Antwerpen, Belgium
Member Since: June 09, 2002
entire network: 2,029 Posts
KitMaker Network: 0 Posts
Member Since: June 09, 2002
entire network: 2,029 Posts
KitMaker Network: 0 Posts
Posted: Tuesday, November 19, 2002 - 09:04 PM UTC
Hi matt,
I used 3 mm plastic rod, sorry for the confusion #:-)
I used 3 mm plastic rod, sorry for the confusion #:-)