Hi All
Another question. I am now building my P47D Thunderbolt , and I am trying to polish out the mold line on the clear gun sight. I have a "Flex-i-file" polisher / finisher sanding stick, but have forgotten how to use it. It has three different grits but I'm not sure which order to use them. I have been experimenting , but so far it hasn't gotten very clear.
Can anyone help me?
Thanks All !!
Hosted by Jim Starkweather
Need "Flex-i-file" polisher / finisher help
tek2
New York, United States
Member Since: June 06, 2002
entire network: 156 Posts
KitMaker Network: 0 Posts
Member Since: June 06, 2002
entire network: 156 Posts
KitMaker Network: 0 Posts
Posted: Monday, September 22, 2003 - 10:02 AM UTC
Posted: Monday, September 22, 2003 - 10:32 AM UTC
Hi there
Sorry if this is a bit generic but...
Start with the coarsest grit and work progressively through to the smoothest.
For the final pass, I use a nail buffer - to get a really smooth finish.
Hope this helps
Rowan
Sorry if this is a bit generic but...
Start with the coarsest grit and work progressively through to the smoothest.
For the final pass, I use a nail buffer - to get a really smooth finish.
Hope this helps
Rowan
TwistedFate
Virginia, United States
Member Since: February 11, 2003
entire network: 805 Posts
KitMaker Network: 0 Posts
Member Since: February 11, 2003
entire network: 805 Posts
KitMaker Network: 0 Posts
Posted: Monday, September 22, 2003 - 11:21 AM UTC
I'll be a bit more specific than Merlin.
On the side with 2 grits, start with the gray, then the white. Then flip it over to the all gray side and use that to buff it out and shine it up. Dip that sucker in Future when you are done and your done.
On the side with 2 grits, start with the gray, then the white. Then flip it over to the all gray side and use that to buff it out and shine it up. Dip that sucker in Future when you are done and your done.
tek2
New York, United States
Member Since: June 06, 2002
entire network: 156 Posts
KitMaker Network: 0 Posts
Member Since: June 06, 2002
entire network: 156 Posts
KitMaker Network: 0 Posts
Posted: Monday, September 22, 2003 - 01:06 PM UTC
Thanks Colonel T. Fate
That's exactly what I was looking for !
and it means that Merlin is also right.
But it must be the Future that does the trick, cause I can't do it with just the file. It comes out lightly foggy.
There must be something else I'm missing.
Thanks everyone, I knew you'd know.
That's exactly what I was looking for !
and it means that Merlin is also right.
But it must be the Future that does the trick, cause I can't do it with just the file. It comes out lightly foggy.
There must be something else I'm missing.
Thanks everyone, I knew you'd know.
Iron-Fist
Idaho, United States
Member Since: August 09, 2002
entire network: 101 Posts
KitMaker Network: 0 Posts
Member Since: August 09, 2002
entire network: 101 Posts
KitMaker Network: 0 Posts
Posted: Tuesday, September 23, 2003 - 10:26 AM UTC
Wet sand. That woks really well,
Posted: Tuesday, September 23, 2003 - 11:27 AM UTC
Hi Tek2
Sorry I couldn't be more specific... I never use "name band" sanding sticks
- the drug-store versions are just as good and a lot cheaper...
That said... I do recommend Micro Mesh polishing cloths... they're not cheap - but the results are amazing... :-)
All the best
Rowan
Sorry I couldn't be more specific... I never use "name band" sanding sticks
- the drug-store versions are just as good and a lot cheaper...
That said... I do recommend Micro Mesh polishing cloths... they're not cheap - but the results are amazing... :-)
All the best
Rowan