hey
how would you attach antenera's to a tank
cheers
matt
Hosted by Jim Starkweather
attaching antenera's ????
USMarine
Christchurch, New Zealand
Member Since: September 17, 2005
entire network: 475 Posts
KitMaker Network: 0 Posts
Member Since: September 17, 2005
entire network: 475 Posts
KitMaker Network: 0 Posts
Posted: Saturday, March 25, 2006 - 04:58 AM UTC
Erik67
Buskerud, Norway
Member Since: July 31, 2005
entire network: 1,871 Posts
KitMaker Network: 376 Posts
Member Since: July 31, 2005
entire network: 1,871 Posts
KitMaker Network: 376 Posts
Posted: Saturday, March 25, 2006 - 05:06 AM UTC
With glue...
I usually use a small drill in a pin wise and drill out the antenna base. Then I attach the antenna with ordinary plastic cement or super glue.
Erik
I usually use a small drill in a pin wise and drill out the antenna base. Then I attach the antenna with ordinary plastic cement or super glue.
Erik
blaster76
Texas, United States
Member Since: September 15, 2002
entire network: 8,985 Posts
KitMaker Network: 2,270 Posts
Member Since: September 15, 2002
entire network: 8,985 Posts
KitMaker Network: 2,270 Posts
Posted: Saturday, March 25, 2006 - 07:21 AM UTC
On a model----with glue
In real life---they screw in
Sorry I just couldn't resist :-) :-) :-)
In real life---they screw in
Sorry I just couldn't resist :-) :-) :-)
Posted: Saturday, March 25, 2006 - 07:47 AM UTC
Quoted Text
With glue...
Erik
Hey! No sh*t Sherlock? :-) :-) :-)
LO Erik.
USMarine
Christchurch, New Zealand
Member Since: September 17, 2005
entire network: 475 Posts
KitMaker Network: 0 Posts
Member Since: September 17, 2005
entire network: 475 Posts
KitMaker Network: 0 Posts
Posted: Saturday, March 25, 2006 - 07:54 AM UTC
well i was only say because on the sherman there isnt a hole put it (turrert) into jst were a plastic looking spring comes up,should i take it out and drill a hole or glue it to it straight on.
matt
matt
rebelsoldier
Arizona, United States
Member Since: June 30, 2004
entire network: 1,336 Posts
KitMaker Network: 570 Posts
Member Since: June 30, 2004
entire network: 1,336 Posts
KitMaker Network: 570 Posts
Posted: Saturday, March 25, 2006 - 02:11 PM UTC
i have found that drill and glue is best for me, it gives the antennae a secure holding as well.
i use .010 guitar strings for my antennae
reb
i use .010 guitar strings for my antennae
reb
Posted: Saturday, March 25, 2006 - 03:30 PM UTC
Hi Matt,
drilling a small hole is definitely a help. Get hold of something called a "pin vise" which looks like a pencil or small screwdriver with a locking collet (or jaw) on the end. This grips what is a very small drill bit and makes it far easier to control. They aren't expensive, (I got a set for about £4) and come either as a set with differing drill widths or one item with a chuck like a power drill. Either way, it's a very handy thing to have and takes Dremel or equivalent drill bits.
Do it by hand. A power tool like a Dremel will just burn the plastic.
drilling a small hole is definitely a help. Get hold of something called a "pin vise" which looks like a pencil or small screwdriver with a locking collet (or jaw) on the end. This grips what is a very small drill bit and makes it far easier to control. They aren't expensive, (I got a set for about £4) and come either as a set with differing drill widths or one item with a chuck like a power drill. Either way, it's a very handy thing to have and takes Dremel or equivalent drill bits.
Do it by hand. A power tool like a Dremel will just burn the plastic.
Pedro
Wojewodztwo Pomorskie, Poland
Member Since: May 26, 2003
entire network: 1,208 Posts
KitMaker Network: 88 Posts
Member Since: May 26, 2003
entire network: 1,208 Posts
KitMaker Network: 88 Posts
Posted: Saturday, March 25, 2006 - 03:39 PM UTC
you can also use a hypodermic needle (my english baad, someone correct me if this isn't the appropriate word)
of appropriate size to drill small holes by hand. It's quite handy and works for me.
Pedro
of appropriate size to drill small holes by hand. It's quite handy and works for me.
Pedro