Sorry if this is the wrong forum, but I'm looking to redesign my spraybooth and I'm wondering what the opinion is about fume extractor placement..
Currently I have a booth that is 24" deep by 36" high by 36" wide, I like the added height for lighting as well as ease of work area.The extractor is mounted on top.
I am using a kitchen range hood for the extractor and am pleased with its performance as it does move alot of air but.....
I notice quite a bit of overspray/dust build up and although I clean it I'm still getting dust in the paint. Should I re configure the extractor to sit at the back of the booth as I have used in bigger commercial booths in the past, or downdraft, where the extractor sits upsidedown at the base of the booth as I've heard some other booths are configured?
Once again I apololgize if this is the wrong forum.
Thanks
Peter
Hosted by Jim Starkweather
DIY spraybooths - downdraft, updraft or....
Joker
British Columbia, Canada
Member Since: May 28, 2004
entire network: 813 Posts
KitMaker Network: 203 Posts
Member Since: May 28, 2004
entire network: 813 Posts
KitMaker Network: 203 Posts
Posted: Sunday, July 31, 2005 - 03:32 AM UTC
capnjock
United States
Member Since: May 19, 2003
entire network: 860 Posts
KitMaker Network: 340 Posts
Member Since: May 19, 2003
entire network: 860 Posts
KitMaker Network: 340 Posts
Posted: Sunday, July 31, 2005 - 04:44 AM UTC
I use a furnace filter in front of the fan so I can change it out when the overspray is to much. (I had to install the rails for the filter myself).
capnjock
capnjock
matt
Campaigns Administrator
New York, United States
Member Since: February 28, 2002
entire network: 5,957 Posts
KitMaker Network: 2,626 Posts
Member Since: February 28, 2002
entire network: 5,957 Posts
KitMaker Network: 2,626 Posts
Posted: Sunday, July 31, 2005 - 07:13 AM UTC
i built my own. I built a downdraft style with the fans mounted in the back / bottom. I too use a furnace filter (actually 2 stacked) as a filter. The vent tube runs up behind the booth and out ogf the basement.
jRatz
North Carolina, United States
Member Since: March 06, 2004
entire network: 1,171 Posts
KitMaker Network: 0 Posts
Member Since: March 06, 2004
entire network: 1,171 Posts
KitMaker Network: 0 Posts
Posted: Sunday, July 31, 2005 - 01:20 PM UTC
I built mine as down-draft to avoid all the dust issues. The booth sits a bit high (I have to stand to brush) so the fan can exhaust out the window. I also use furnace filters between the paint area & the fan.
See my workshop pictures in My Gallery for a booth shot -- no details of fan & stuff ....
John
See my workshop pictures in My Gallery for a booth shot -- no details of fan & stuff ....
John
umustb
Singapore / 新加坡
Member Since: April 27, 2005
entire network: 1,396 Posts
KitMaker Network: 940 Posts
Member Since: April 27, 2005
entire network: 1,396 Posts
KitMaker Network: 940 Posts
Posted: Sunday, July 31, 2005 - 02:05 PM UTC
Since the topic is here... i was wondering if you guys came across any websites with pictures of how to DIY your own spraybooths?
straightedge
Ohio, United States
Member Since: January 18, 2004
entire network: 1,352 Posts
KitMaker Network: 571 Posts
Member Since: January 18, 2004
entire network: 1,352 Posts
KitMaker Network: 571 Posts
Posted: Monday, August 01, 2005 - 02:42 AM UTC
I found a diagram for a painting booth that pretty much goes into detail on a real good booth, it also explains about how to much draw will pull dust from your room, and get on your work.
This all made good sense to me, they had the numbers per million and everything, but the one thing I did remember was to stay away from upper venting, that in time it could lead to also having dirt drop on your work.
They also had a vent to open so they could control the air flow over your work, so it wouldn't draw to much, I'll try to find it if you like, it shows all this plus the blue prints on how to make it, with the vent pipes and everything.
Kerry.
This all made good sense to me, they had the numbers per million and everything, but the one thing I did remember was to stay away from upper venting, that in time it could lead to also having dirt drop on your work.
They also had a vent to open so they could control the air flow over your work, so it wouldn't draw to much, I'll try to find it if you like, it shows all this plus the blue prints on how to make it, with the vent pipes and everything.
Kerry.
Jacques
Minnesota, United States
Member Since: March 04, 2003
entire network: 4,630 Posts
KitMaker Network: 0 Posts
Member Since: March 04, 2003
entire network: 4,630 Posts
KitMaker Network: 0 Posts
Posted: Monday, August 01, 2005 - 03:37 AM UTC
Yes, if you do find the info, please post it here...There are many, ,yself included, who would find it usefull.
Joker
British Columbia, Canada
Member Since: May 28, 2004
entire network: 813 Posts
KitMaker Network: 203 Posts
Member Since: May 28, 2004
entire network: 813 Posts
KitMaker Network: 203 Posts
Posted: Monday, August 01, 2005 - 08:37 AM UTC
That would be great Kerry, thanks
Joker
Joker
straightedge
Ohio, United States
Member Since: January 18, 2004
entire network: 1,352 Posts
KitMaker Network: 571 Posts
Member Since: January 18, 2004
entire network: 1,352 Posts
KitMaker Network: 571 Posts
Posted: Tuesday, August 02, 2005 - 09:19 PM UTC
I don't know how to post things like that, if I did, I sure would have done a few by now.
I got the digram for the box in my files, but I'll try to find the whole story again, then give somebody else the address.
Kerry
I got the digram for the box in my files, but I'll try to find the whole story again, then give somebody else the address.
Kerry
Silantra
Putrajaya, Malaysia
Member Since: March 04, 2004
entire network: 2,511 Posts
KitMaker Network: 1,296 Posts
Member Since: March 04, 2004
entire network: 2,511 Posts
KitMaker Network: 1,296 Posts
Posted: Tuesday, August 02, 2005 - 09:28 PM UTC
Hi all,
here's a good article on designing spray booth. I found it usefull. Lot of techie stuff inside
click here
here's a good article on designing spray booth. I found it usefull. Lot of techie stuff inside
click here
jRatz
North Carolina, United States
Member Since: March 06, 2004
entire network: 1,171 Posts
KitMaker Network: 0 Posts
Member Since: March 06, 2004
entire network: 1,171 Posts
KitMaker Network: 0 Posts
Posted: Wednesday, August 03, 2005 - 12:57 PM UTC
http://www.briansmodelcars.com/tutorials/tutorial.asp?TutorialID=23&CurPage=1
I used this for much of my booth design; all errors and problems are my own.
OOPS, duplicated Silantra's post, sorry -- but then I guess it's two votes for the info being valuable.
John
I used this for much of my booth design; all errors and problems are my own.
OOPS, duplicated Silantra's post, sorry -- but then I guess it's two votes for the info being valuable.
John
Joker
British Columbia, Canada
Member Since: May 28, 2004
entire network: 813 Posts
KitMaker Network: 203 Posts
Member Since: May 28, 2004
entire network: 813 Posts
KitMaker Network: 203 Posts
Posted: Wednesday, August 03, 2005 - 04:45 PM UTC
Thanks for the info
Cheers
Joker
Cheers
Joker
straightedge
Ohio, United States
Member Since: January 18, 2004
entire network: 1,352 Posts
KitMaker Network: 571 Posts
Member Since: January 18, 2004
entire network: 1,352 Posts
KitMaker Network: 571 Posts
Posted: Wednesday, August 03, 2005 - 09:44 PM UTC
That's the one