I guess I must be crazy or love to go blind making miniscule objects but does anyone have an idea how I can make shotgun shells? Don't need a lot, maybe about half a dozen so I can pin them on my 1:35 SF figure's vest.
I could use pencil lead or stretched sprue but how do I make the slightly flattened and wider end at the cap?
Thanks a bunch, a shotgun pellet bunch of course.
Scratchbuilders!: Armor/AFV
This is a group for armor scratchbuilding questions, topics and projects.
This is a group for armor scratchbuilding questions, topics and projects.
Hosted by Mike Kirchoff
Scratchbuilding shotgun bullets
beachbum
Kuala Lumpur, Malaysia
Member Since: March 05, 2004
entire network: 1,735 Posts
KitMaker Network: 0 Posts
Member Since: March 05, 2004
entire network: 1,735 Posts
KitMaker Network: 0 Posts
Posted: Thursday, June 24, 2004 - 09:36 PM UTC
Grumpyoldman
Consigliere
Florida, United States
Member Since: October 17, 2003
entire network: 15,338 Posts
KitMaker Network: 5,072 Posts
Member Since: October 17, 2003
entire network: 15,338 Posts
KitMaker Network: 5,072 Posts
Posted: Thursday, June 24, 2004 - 10:15 PM UTC
Contrail rod.
Simply roll your #11 blade back and forth, and it will cut nicely, leaving a very tiny raise edge, along with a flat end. Then just simply remove the raised edge from one end of each shell.
Contrail Rod comes in different diameters, I usually buy a few packs at a time, along with the Contrail tubes. I get mine mail order from :
http://www.aeroclub-models.com/Aeroclub
Hope that helps
Simply roll your #11 blade back and forth, and it will cut nicely, leaving a very tiny raise edge, along with a flat end. Then just simply remove the raised edge from one end of each shell.
Contrail Rod comes in different diameters, I usually buy a few packs at a time, along with the Contrail tubes. I get mine mail order from :
http://www.aeroclub-models.com/Aeroclub
Hope that helps
Stahlhelm
Oregon, United States
Member Since: April 03, 2004
entire network: 414 Posts
KitMaker Network: 0 Posts
Member Since: April 03, 2004
entire network: 414 Posts
KitMaker Network: 0 Posts
Posted: Friday, June 25, 2004 - 12:06 AM UTC
Turn em' on a lathe.
Cody
Cody
Grumpyoldman
Consigliere
Florida, United States
Member Since: October 17, 2003
entire network: 15,338 Posts
KitMaker Network: 5,072 Posts
Member Since: October 17, 2003
entire network: 15,338 Posts
KitMaker Network: 5,072 Posts
Posted: Friday, June 25, 2004 - 06:33 AM UTC
Not everyone is fortunate enough to have a lathe, or talented enough to use one............. LOL
matt
Campaigns Administrator
New York, United States
Member Since: February 28, 2002
entire network: 5,957 Posts
KitMaker Network: 2,626 Posts
Member Since: February 28, 2002
entire network: 5,957 Posts
KitMaker Network: 2,626 Posts
Posted: Friday, June 25, 2004 - 06:53 AM UTC
1/35 scale shot shells on a lathe????? HA
that's like a number 74 drill bit in diameter.... .021
Tiny
that's like a number 74 drill bit in diameter.... .021
Tiny
Stahlhelm
Oregon, United States
Member Since: April 03, 2004
entire network: 414 Posts
KitMaker Network: 0 Posts
Member Since: April 03, 2004
entire network: 414 Posts
KitMaker Network: 0 Posts
Posted: Friday, June 25, 2004 - 11:35 AM UTC
Matt,
I've made HO-scale tire valve stems with a stem diameter of .006. One customer repeatedly ordered large quantities of 1/43 tire valve stems which had a stem diameter of about .012. It's really not too difficult just so long as you keep the tool sharp and don't take huge cuts. Visit my selected link.
Cody
I've made HO-scale tire valve stems with a stem diameter of .006. One customer repeatedly ordered large quantities of 1/43 tire valve stems which had a stem diameter of about .012. It's really not too difficult just so long as you keep the tool sharp and don't take huge cuts. Visit my selected link.
Cody
BroAbrams
Washington, United States
Member Since: October 02, 2002
entire network: 1,546 Posts
KitMaker Network: 494 Posts
Member Since: October 02, 2002
entire network: 1,546 Posts
KitMaker Network: 494 Posts
Posted: Friday, June 25, 2004 - 03:58 PM UTC
I would use stretched sprue or styrene rod and heat one end, like when you do the stem thingy's on vinyl track, mushroom it out, then after it cools, sand the mushroom head to shape. You might also use a dremel tool as a mini lathe and mount the sprue in it to turn.
Rob
Rob
Cuhail
Illinois, United States
Member Since: February 10, 2004
entire network: 2,058 Posts
KitMaker Network: 787 Posts
Member Since: February 10, 2004
entire network: 2,058 Posts
KitMaker Network: 787 Posts
Posted: Saturday, June 26, 2004 - 06:37 AM UTC
I use my drill press as a lathe and a round needle file point as a cutting tool! I can usually mill stuff (wood, plastic, soft metal) to a very small dia.
Cuhail
Cuhail
Grumpyoldman
Consigliere
Florida, United States
Member Since: October 17, 2003
entire network: 15,338 Posts
KitMaker Network: 5,072 Posts
Member Since: October 17, 2003
entire network: 15,338 Posts
KitMaker Network: 5,072 Posts
Posted: Saturday, June 26, 2004 - 07:15 AM UTC
Cody is probably one of the finest machinest in the hobby, turning out turned and milled parts that are beyond belief.
Stahlhelm
Oregon, United States
Member Since: April 03, 2004
entire network: 414 Posts
KitMaker Network: 0 Posts
Member Since: April 03, 2004
entire network: 414 Posts
KitMaker Network: 0 Posts
Posted: Saturday, June 26, 2004 - 09:29 AM UTC
Well shucks, Dave.
Thanks,
Cody
Thanks,
Cody
beachbum
Kuala Lumpur, Malaysia
Member Since: March 05, 2004
entire network: 1,735 Posts
KitMaker Network: 0 Posts
Member Since: March 05, 2004
entire network: 1,735 Posts
KitMaker Network: 0 Posts
Posted: Monday, June 28, 2004 - 04:40 PM UTC
Thanks for the input, guys. Unfortunately I have no access to a lathe. Two options, dig around the kitchen for something I can use (without the little woman's knowledge of course) or get the creative juices going and figure something I can modify like parts of a superstructure of a 1:700 scale ship.
Thanks again.
Thanks again.