Scratchbuilders!: Armor/AFV
This is a group for armor scratchbuilding questions, topics and projects.
This is a group for armor scratchbuilding questions, topics and projects.
Hosted by Mike Kirchoff
HYdraulic Hose fittings
Trackjam
Ontario, Canada
Member Since: April 12, 2002
entire network: 831 Posts
KitMaker Network: 210 Posts
Member Since: April 12, 2002
entire network: 831 Posts
KitMaker Network: 210 Posts
Posted: Saturday, February 07, 2004 - 06:22 AM UTC
Does anyone know of a 1/35 supplier for hydraulic hose fittings? I'm doing a recovery vehicle and trying to replicate as close as possible the hose attachements.
ekaufman
Haifa, Israel
Member Since: June 17, 2002
entire network: 217 Posts
KitMaker Network: 0 Posts
Member Since: June 17, 2002
entire network: 217 Posts
KitMaker Network: 0 Posts
Posted: Saturday, February 07, 2004 - 06:55 AM UTC
That would be very intresting to know,i didnt use any on my recent project (M-107 SPG) with a lot of hydraulics. what about using hex rod in a diameter little bigger then the hose?
Eran
Eran
matt
Campaigns Administrator
New York, United States
Member Since: February 28, 2002
entire network: 5,957 Posts
KitMaker Network: 2,626 Posts
Member Since: February 28, 2002
entire network: 5,957 Posts
KitMaker Network: 2,626 Posts
Posted: Saturday, February 07, 2004 - 12:51 PM UTC
straightedge
Ohio, United States
Member Since: January 18, 2004
entire network: 1,352 Posts
KitMaker Network: 571 Posts
Member Since: January 18, 2004
entire network: 1,352 Posts
KitMaker Network: 571 Posts
Posted: Saturday, February 07, 2004 - 02:08 PM UTC
I see where your coming from, that 1/24-1/25 car lines ought to be just about right for the 1/35 Tank lines, good idea.
I went to that Detail Masters site, and they do have the options of .020", .025", .035", .045", .060", .080", .100" all it takes is just figuring what size you need.
The best I could figure it out they are a little over a dollar a piece for each part, but I do believe they would make a beautiful hydraulic line.
I went to that Detail Masters site, and they do have the options of .020", .025", .035", .045", .060", .080", .100" all it takes is just figuring what size you need.
The best I could figure it out they are a little over a dollar a piece for each part, but I do believe they would make a beautiful hydraulic line.
Trackjam
Ontario, Canada
Member Since: April 12, 2002
entire network: 831 Posts
KitMaker Network: 210 Posts
Member Since: April 12, 2002
entire network: 831 Posts
KitMaker Network: 210 Posts
Posted: Wednesday, February 11, 2004 - 01:23 PM UTC
Matt,
That is exactly what I had in mind. Thanks for the tip.
That is exactly what I had in mind. Thanks for the tip.
mikeli125
England - North West, United Kingdom
Member Since: December 24, 2002
entire network: 2,595 Posts
KitMaker Network: 1,079 Posts
Member Since: December 24, 2002
entire network: 2,595 Posts
KitMaker Network: 1,079 Posts
Posted: Thursday, February 12, 2004 - 02:22 AM UTC
Paul,
get some telephone wire,
now cut a sectio of lenght you need pull out the strands
you can use this a wiring ect or nick the plastic sheath and pull put the copper core you now have a little bit of hydraulic hose and the copper can be used for grap rails ect
get some telephone wire,
now cut a sectio of lenght you need pull out the strands
you can use this a wiring ect or nick the plastic sheath and pull put the copper core you now have a little bit of hydraulic hose and the copper can be used for grap rails ect
Posted: Thursday, February 12, 2004 - 02:56 AM UTC
Don´t know if this will be detailed enough for you, but when I made hydraulic hoses for my scud launcher, I used cables for remote control cars. The connections were aluninium tray strips wrapped around the cable. Very simple and quick ... no need to be painted either... just get the suitable colour cable!
8)
8)
Trackjam
Ontario, Canada
Member Since: April 12, 2002
entire network: 831 Posts
KitMaker Network: 210 Posts
Member Since: April 12, 2002
entire network: 831 Posts
KitMaker Network: 210 Posts
Posted: Monday, February 23, 2004 - 02:16 PM UTC
Thanks for the tips. I have ordered some engine detail parts and will let you know how they turn out.
jejack2
Maryland, United States
Member Since: April 09, 2002
entire network: 322 Posts
KitMaker Network: 0 Posts
Member Since: April 09, 2002
entire network: 322 Posts
KitMaker Network: 0 Posts
Posted: Monday, February 23, 2004 - 02:35 PM UTC
Another suggestion would be Solder, for electronics, available at "Radio Shack" cheap, and in different diameters. Paints okay, and is malleable (bendable). you can use hex rod for the fittings.
Trackjam
Ontario, Canada
Member Since: April 12, 2002
entire network: 831 Posts
KitMaker Network: 210 Posts
Member Since: April 12, 2002
entire network: 831 Posts
KitMaker Network: 210 Posts
Posted: Thursday, March 04, 2004 - 01:43 PM UTC
Thanks again for all the tips. I received a trial order from Detail Master. It was exactly what I was looking for. I aso ordered their catalogue which provides a lot more info than is on their website. Nevertheless i can now advance my ARV project a lot faster.
TangoCharlie
Massachusetts, United States
Member Since: September 28, 2003
entire network: 60 Posts
KitMaker Network: 0 Posts
Member Since: September 28, 2003
entire network: 60 Posts
KitMaker Network: 0 Posts
Posted: Friday, April 09, 2004 - 02:02 PM UTC
Try electrical and electronic wires, they come in several gages, the smallest I've used is .015" diameter and they come in many colors, sometimes you don't even have to paint them , a small roll would last you for years.
Best regards and happy modeling.
T. Chouman
Best regards and happy modeling.
T. Chouman
Mech
Ontario, Canada
Member Since: July 20, 2002
entire network: 281 Posts
KitMaker Network: 63 Posts
Member Since: July 20, 2002
entire network: 281 Posts
KitMaker Network: 63 Posts
Posted: Sunday, April 11, 2004 - 01:28 AM UTC
Hi Paul
Another good source for fittings is model trains, especially if the shop carries
after market fittings for N, Ho and O = 1/4 scale. George's Trains, Bayview
Ave. in Toronto used to be one of the best resources for trains.
Cheers
Ralph
Another good source for fittings is model trains, especially if the shop carries
after market fittings for N, Ho and O = 1/4 scale. George's Trains, Bayview
Ave. in Toronto used to be one of the best resources for trains.
Cheers
Ralph
ModlrMike
Alberta, Canada
Member Since: January 03, 2003
entire network: 714 Posts
KitMaker Network: 0 Posts
Member Since: January 03, 2003
entire network: 714 Posts
KitMaker Network: 0 Posts
Posted: Monday, April 12, 2004 - 01:25 PM UTC
You might also try using the little brass fittings on the end of wire guitar strings.
http://www.mezurashii.com/artwork/photos/guitar_strings.jpg
http://www.mezurashii.com/artwork/photos/guitar_strings.jpg
Trackjam
Ontario, Canada
Member Since: April 12, 2002
entire network: 831 Posts
KitMaker Network: 210 Posts
Member Since: April 12, 2002
entire network: 831 Posts
KitMaker Network: 210 Posts
Posted: Wednesday, July 07, 2004 - 02:28 PM UTC
Thanks for the help guys. I went with the Detail Master engine parts. They turned out just as i expected. See my post in Armour under Commonwealth Build-Husky. Highly recommended for the scratchbuilding fanatic
GeneralFailure
European Union
Member Since: February 15, 2002
entire network: 2,289 Posts
KitMaker Network: 532 Posts
Member Since: February 15, 2002
entire network: 2,289 Posts
KitMaker Network: 532 Posts
Posted: Saturday, July 10, 2004 - 12:15 AM UTC
Hey Paul, we look forward to see a picture of the result !
Trackjam
Ontario, Canada
Member Since: April 12, 2002
entire network: 831 Posts
KitMaker Network: 210 Posts
Member Since: April 12, 2002
entire network: 831 Posts
KitMaker Network: 210 Posts
Posted: Wednesday, August 11, 2004 - 09:56 PM UTC
Quoted Text
Hey Paul, we look forward to see a picture of the result !
Thanks for the help. See the bottom of the following thread:
https://armorama.kitmaker.net/forums/28802&page=1
mother
New York, United States
Member Since: January 29, 2004
entire network: 3,836 Posts
KitMaker Network: 1,121 Posts
Member Since: January 29, 2004
entire network: 3,836 Posts
KitMaker Network: 1,121 Posts
Posted: Monday, August 16, 2004 - 01:46 PM UTC
that detail master stuff is great, but pricey too. i'll tell what i like to use. plastic hex rod. first drill the hole size you need at one end. go deep to. then tapper that end down by sanding it and cut to length. glue in your wire, paint. it looks just as good as the store bought parts.
Trackjam
Ontario, Canada
Member Since: April 12, 2002
entire network: 831 Posts
KitMaker Network: 210 Posts
Member Since: April 12, 2002
entire network: 831 Posts
KitMaker Network: 210 Posts
Posted: Tuesday, August 17, 2004 - 04:41 AM UTC
Quoted Text
that detail master stuff is great, but pricey too. i'll tell what i like to use. plastic hex rod. first drill the hole size you need at one end. go deep to. then tapper that end down by sanding it and cut to length. glue in your wire, paint. it looks just as good as the store bought parts.
Another great idea. Thanks. Will try that on my M113 Dozer.